Recent Activity

Activity stream for all registered members at FabricationForum.com.

  1. KKesner replied to the thread How to put a recess into an exsisting metal Chassis.

    If you can get to both sides. I would use a big washer on one side and small one on the other side with a bolt, nut and a flat bar.

    Oct 18, 2017 at 5:28 PM
  2. Dnmeistr-LECS replied to the thread Torchmate down since May 17'.

    Somehow or another when the plasma cutter is being called upon to cut, it is backfeeding current into the Accumove causing it to shut...

    Oct 18, 2017 at 4:50 PM
  3. KKesner replied to the thread Pan table leaking.

    If it is leaking from a seam or small hole I would use 3m 5200 marine sealant

    Oct 18, 2017 at 4:41 PM
  4. Schutte posted a new thread.

    Pan table leaking

    Has anyone had the water pan start to leak. Looks like its under the rail guides. I'm sure its were water was trapped this summer....

    Forum: CNC Cutting

    Oct 18, 2017 at 9:17 AM
  5. Cypress replied to the thread Torchmate down since May 17'.

    Thanks for the info. I will double check the interface. For the past two years I’ve had no issues running my table and have not...

    Oct 17, 2017 at 4:31 PM
  6. Dnmeistr-LECS attached a file to the thread Torchmate down since May 17'.

    We will need to verify the plasma connections are terminated to the correct locations. Off the plasma interface cable you should have...

    Raw Arc Thermal Dynamics Cutmaster 52, Cutmaster 82, Cutmaster 102, Cutmaster 152,.jpg Oct 17, 2017 at 4:24 PM
  7. Cypress posted a new thread.

    Torchmate down since May 17'

    Well the ongoing saga with my table continues. I sent my accumove2 to a place in San Antonio for repairs. After 3 months I get...

    Forum: CNC Cutting

    Oct 16, 2017 at 4:51 PM
  8. Torchmate liked Dnmeistr-LECS's post in the thread How to: replace/upgrade gearboxes.

    The image of the new Micron gear box and coupler adapter, where the two slots line up with each other, you will want to rotate the outer...

    Oct 16, 2017 at 2:22 PM
  9. Torchmate liked nwaPLASMA's post in the thread How to: replace/upgrade gearboxes.

    Good call out. I turned it before I installed it but neglected to get a pic of it that way. Thanks!

    Oct 16, 2017 at 2:22 PM
  10. nwaPLASMA replied to the thread How to: replace/upgrade gearboxes.

    Good call out. I turned it before I installed it but neglected to get a pic of it that way. Thanks!

    Oct 16, 2017 at 9:04 AM
  11. Dnmeistr-LECS replied to the thread Dry run works, but active just Pierces..

    You can turn Ok to Move off in the Tool Library for Tool 1.

    Oct 16, 2017 at 7:46 AM
  12. Dnmeistr-LECS replied to the thread How to: replace/upgrade gearboxes.

    The image of the new Micron gear box and coupler adapter, where the two slots line up with each other, you will want to rotate the outer...

    Oct 16, 2017 at 7:44 AM
  13. nwaPLASMA liked Kchoghead's post in the thread How to: replace/upgrade gearboxes.

    Keep after it Jason. make an old warhorse great again

    Oct 15, 2017 at 6:47 PM
  14. Kchoghead replied to the thread How to: replace/upgrade gearboxes.

    Keep after it Jason. make an old warhorse great again

    Oct 15, 2017 at 6:45 PM
  15. nwaPLASMA attached a file to the thread How to: replace/upgrade gearboxes.

    My test cut. [ATTACH] [ATTACH]

    IMG_0594.JPG IMG_0595.JPG Oct 15, 2017 at 6:24 PM
Loading...