Torchmate
Last Activity:
Aug 9, 2021
Joined:
Nov 25, 2015
Messages:
250
Likes Received:
58
Trophy Points:
108

Awarded Medals 6

Share This Page

Torchmate

Administrator

Staff Member

Design | Cut | Build Episode 6 is out! Sep 6, 2018

Torchmate was last seen:
Aug 9, 2021
    1. Rcktscientist
      Rcktscientist
      So today my 4X4 GS / Accumotive 2 crashed, dislodging the torch and it DIDN'T shut down and kept firing dragging along the metal while completely dislodged. Spoke to Alex and he had never seen that before. I videoed it and got it all. I was hoping I could upload the video here but do not see how. The last couple of jobs the torch dwelled a long time, probably 4 or 5 seconds before firing after initial touch off.
    2. tjwick
      tjwick
      I bought a prepaid design and when I import the design into torchmate and make a path then create tool path it changes the size of the the 9 squares around the design. How do I stop that from happening. Also the program creates both male and female lead ins.
    3. Ole school
      Ole school
      I have the old 401A signal generator and it will not power on. I have used it 3 years and no issues, Any suggestions on how to troubleshoot it? Thanks
    4. tjwick
      tjwick
      When I make bridges for letters and I go to weld them the design is cutting out all the bridge, not just the part I want welded. I have tried everything I know to stop this to no avail. What am I doing wrong?
      1. TJCutter
        TJCutter
        Did you get an answer to this question?
        Nov 14, 2020
    5. Shea
      Shea
      Is there a wiring diagram for the accumove 3 for the limit switches? I am trying to wire some prox switches for my limit switches for the datum and can't figure out if the white or black wire is the trigger or ground. Any help would be greatly appreciated.
    6. Ty Barker
      Ty Barker
      I can not seem to figure out what changed but when I go save my G-code all I am getting is .nc file format and don't know what to do to get it to produce .gm files. Can someone please help me figure out what I did or how to get back to making .gm files
    7. Torchmate
      Torchmate
      Design | Cut | Build Episode 6 is out!
    8. Torchmate
      Torchmate
      Design | Cut | Build is coming!
    9. Dave Cotton
      Dave Cotton
      Just set up a 4800 with 80 amp unit. single stage compressor with 3 heads about 10' away. Heated garage.
      Right out of the tank comes a regulator / sediment bowl filter ..
      Q; Do I need to get a dryer just befor the machine or can I get away with a good quality filter just before the machine?
      1. Torchmate
        Torchmate
        Hi Dave, post this in the forum area under CNC Cutting for a response! Thanks!
        Dec 6, 2017
      2. TJCutter
        TJCutter
        My experience says you can't have too many air dryers as long as you have plenty of pressure.
        Nov 14, 2020
    10. ArcedOut
      ArcedOut
      Can anyone give me an idea of what compressor to buy? I’ll be using the FlexCut 80 and the plate marker.
      1. Torchmate
        Torchmate
        Hi! Post this in the forum area under CNC Cutting for a response! Thanks!
        Dec 6, 2017
    11. Raechel Brown
      Raechel Brown
      In need of some help with a design for my sheriffs dept and in a time crunch. Can someone help me out with design?
      1. Raechel Brown
        Raechel Brown
        Not sure on how much to post a pic of what I'm needing?
        Aug 14, 2017
      2. Torchmate
        Torchmate
        Raechel, please post in the main forum area. Thank you.
        Aug 14, 2017
    12. IronsideCustoms
      IronsideCustoms
      Hello, I have a torchmateX 5x10 with torchmate 3 software. I M trying gererate some G-code in the cad and I can seem to figure out how to change the feed rate for the tools when going to G-code. While setting up my tool paths I enter the feed rate I want, but when I generate the g-code the feed rate is at like 1500 when I set it to 90 ? How do I fix this other than manually changing it in the G-code.
      1. Torchmate
        Torchmate
        Hello! Please post this request on the forums and you'll get help! Thank you!
        May 10, 2017
    13. Matt
      Matt
      Is it possible to get my name changed on here?
  • Loading...
  • Loading...
  • Signature

    Check out Torchmate University http://torchmate.com/university- Your #1 resource for CAD training and learning how to operate your table!
  • Loading...
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice