New Profile Posts

  1. Ole school
    Ole school Torchmate
    I have the old 401A signal generator and it will not power on. I have used it 3 years and no issues, Any suggestions on how to troubleshoot it? Thanks
  2. nick goimez
    nick goimez John Bethers
    id love to use your saw dxf if possible
  3. tjwick
    tjwick Torchmate
    When I make bridges for letters and I go to weld them the design is cutting out all the bridge, not just the part I want welded. I have tried everything I know to stop this to no avail. What am I doing wrong?
    1. TJCutter
      Did you get an answer to this question?
      Nov 14, 2020
  4. John McLemore
    John McLemore Larry Cameron
    Larry, my name is John McLemore and I am in dire need of info on the chip you purchased from Onexia. My machine is doing the same as yours did, "no motor detected". Could you please tell me the chip number and contact person at Onexia? Any info will be huge help! Thank you!
  5. Shea
    Shea Torchmate
    Is there a wiring diagram for the accumove 3 for the limit switches? I am trying to wire some prox switches for my limit switches for the datum and can't figure out if the white or black wire is the trigger or ground. Any help would be greatly appreciated.
  6. Ty Barker
    Ty Barker Torchmate
    I can not seem to figure out what changed but when I go save my G-code all I am getting is .nc file format and don't know what to do to get it to produce .gm files. Can someone please help me figure out what I did or how to get back to making .gm files
  7. Faren Nichols
    Faren Nichols LECS-Chad
    Hey, do you think you could possibly help me with the my cuts look.the insides of letters and cut outs are super jagged and look terrible!
  8. Chris Therriault
    Chris Therriault John Bethers
    Hello, i was curious if i could get/purchase the dxf files for your dewalt metal saw table? What an awesome design!
  9. Storm
    Almost done with classes
  10. Shea
    Shea LECS-Chad
    I just received the accumove 3 upgrade for my Torchmate 2 table I ordered back in Feb. and am trying to get it installed any help would be greatly appreciated.
  11. Shea
    Shea LECS-Chad
    where does the big plug in the accumove 3 vfc box plug into?
  12. Storm
    Currently taking classes.
  13. bruce chouquer
    bruce chouquer
    how do i get my grid lines back to a thin black line ?
  14. Anne Razzolini
    Anne Razzolini
    Looking for the best digitizer for the 4400
  15. Sundui
    Torchmate X It's not moving after holding Datum after that everything is not working such as jogging MVC test say all 1234 is 200V
  16. nandy
    I need help with importing an image and cutting it to make center pieces for a Ball
  17. Maxwell
    Maxwell LECS-Chad
    I have a 1.3 Mb pdf file to upload to a forum. Is that possible? I looked at the tools for replies and can't see how to insert a pdf.
    1. LECS-Chad
      I dont believe PDFs have issues. try dragging dropping into the post.
      May 28, 2019
  18. LECS-Chad
  19. John O'Neill
    John O'Neill
    I am trying to find a instructional video on how to use the torchmate to manually cut material while still on the table.
  20. Galen Nelson
    Galen Nelson
    sensing delay
  1. This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
    By continuing to use this site, you are consenting to our use of cookies.
    Dismiss Notice